Maxstore · layout examples

Documented racking project designs

Capacity, dimensions and structural solutions from supplied drawings and specifications. These materials show the project scope; they do not verify completion dates or operating results.

Materials prepared on 15 October 2026 · responsible person: Yu. P. Subbotin

Drive-in storage: 168 pallet locations

Project based on a drawing and commercial specification

  • The plan shows 144 locations for loads of 1200×800×750 mm weighing up to 450 kg, and 24 locations for loads of 1200×800×1600 mm weighing up to 900 kg.
  • Block dimensions on the plan: 5784×6800 mm; overall elevation height: 5893 mm.
  • The specification dated 20 June 2025 lists 20 SZo 80 frames, 5800 mm high and 1000 mm deep.

Design capacity: 168 locations, calculated as 144 + 24; actual operating performance is not provided.

Technical parameters from supplied specifications and drawings; installation completion is unconfirmed.

Drive-In / Drive-Through racking →

Shelving mezzanine: January 2026 version

Project based on a drawing and commercial specification

  • Specification dated 13 January 2026: 36 SZo 80 frames, 4000 mm high, with depths of 800 and 1100 mm.
  • Drawing height: 4003 mm; load per tier: 300 kg; floor load: 200 kg/m².
  • Room plan: 12100×8000 mm; row length: 5738 mm; the room area is not the decking area.

The project provides a second level for manual storage; the effect on speed and revenue has not been measured.

Technical parameters from supplied specifications and drawings; installation completion is unconfirmed.

Shelving-supported mezzanines →

Compact mezzanine: June 2026 version

Project based on a drawing and commercial specification

  • Specification dated 8 June 2026: 15 SZo 80 frames, 600/1200 mm deep and 3900/4100 mm high.
  • Drawing: four spans of 1500 mm per row; length: 6424 mm; main block width: 4400 mm.
  • Drawing loads: 400/800 kg per tier, depending on depth; deck load: 300 kg/m².

The project distributes shelving storage and aisles across two levels; this is a different version from the January design.

Technical parameters from supplied specifications and drawings; installation completion is unconfirmed.

Shelving-supported mezzanines → Combined mezzanines →

Cantilever storage on five frames

Project: component correspondence established by dimensions

  • Specification dated 20 August 2025: five SZok 100 frames, 2000 mm high; ten cantilever arms, each 600 mm long.
  • Drawing 201456: distributed load of 400 kg per arm and up to 2500 kg per frame.
  • Four spans; total length: 4316 mm. Dimensions match the quotation; the quotation number is not shown on the drawing.

A configuration for long goods is described; installation completion data is unavailable.

Technical parameters from supplied specifications and drawings; installation completion is unconfirmed.

Cantilever racking →

Two-level tyre warehouse

Project based on two drawings

  • Plan and elevation: width 23000 mm; height: 4403 mm; deck level: 2397 mm.
  • Tiers of 2700/1250 mm are specified, with loads of 2000/1000 kg respectively; floor load: 250 kg/m².
  • The plan explicitly states that stairs are not included in the supply; warehouse lifting equipment is prohibited on the assembled deck.

The tyre warehouse is documented as divided into two levels. The link to a pricing document and the final supply are not established by the documents.

Technical parameters from supplied specifications and drawings; installation completion is unconfirmed.

Tyre and wheel racking → Pallet-rack-supported mezzanines →

Shelving and cantilever equipment for prop storage

Configuration according to issued invoices

  • Invoice No. 318 dated 4 September 2026: 18 SZok 120 frames, 4200 mm high, and 54 arms, 1200 mm long.
  • Invoice No. 319: 132 type-563 frames, 3700 mm high, 500/800 mm deep; B2 beams and assembled SH shelves.

The product list on the issued invoices is confirmed; payment, shipment and installation are unconfirmed.

Products on issued invoices; shipment, payment and installation are unconfirmed.

Shelving → Cantilever racking →

The load rating applies to the specified drawing and configuration. It cannot be transferred to racking with a different profile, height or configuration. Actual supply and installation are accepted under separate documents.
Data sheets and instructions →Prices and budget →